Bartelt Packager, RH IM 7-12 (7 inch-12 station) w/All Fill B 350E auger filler, Machine No. 580, horizontal form/fill/ seal, E.M.P. registration control unit, equipped with side seal embossing and mechanical hole punch. It has the position for a second filler head. We have run an additional auger filler in that position as well as a volumetric filler in that position. Tear notch and various types auger tooling setups also available separately. Choose from 2 in., 3 1/2 in., 4 in., or 6 in. bag clamps. Very reliable packager. 3 phase 208-220/440 VAC. Selling because of production shut down.

Bartelt horizontal form, fill, and seal Packager, Model RH IM 6-7 (6 inch-7 station) w/B Filler, Machine No. 336, horizontal form/fill/ seal, Tritronics registration unit (Color Mark II, Model CMS 2B), auxiliary equipment such as embossing and various types auger tooling setups available separately. Last ran 60 packages per minute on 1-gram fill. Smooth/quiet running machine. 3 phase 208-220 VAC. Selling because of production shut down.

Case Sealer/Carton Taper, The Loveshaw Corporation, Model 304/19, S.N. 159183300, 110 Volt, 9.6 Amp. Top & Bottom Sealing Heads, 2 in. x 6 ft. Side Pull Belts, Product Loading ?anvil?, unit currently has Lincoln Coder, Model 90-2L-I

Used- Westfalia SA-1-02-175 Desludger Disc Centrifuge. 316 Stainless steel construction, product contact areas, separator design (liquid/liquid/solids separation), light phase centripetal pump liquid discharge, gravity over-flow heavy phase liquid discharge. Suitable for pilot plant operation. Can be set up as a clarifier or a separator. (2-phase or 3-phase). Driven by a 2 hp (1.5kW), 3/60/208 volt, motor. Control panel with Allen Bradley panelview 550, Allen Bradley micrologix 1000, Toshiba G7 speed drive. All mounted on portable cart. Built 2004.

This is Chiller with 800 HP Motor, Dual pump water circ skid. All idled in early 2013, stored in warehouse since then. Chiller 1600 ton. Complete package includes chiller, controls, condensers, dual pump skid. York Code Pak centrifugal screw compressor with pump and glycol water recirculation package. Built in 1995, complete reconditioning 2006, new controls 2011, eddy current testing 2011 (passed), Motor rebuilt 2005. Designed for Refrigerant 134A. (not included). Unit Model YKQEQCJ2-CBCS, s/n GBEM052065. Compressor model YDHA73DD, code EB. Has integral Cooler heat exchanger 2 passes. Hours 51,062 with 1060 starts. Controls have recently been replaced in 2011 just prior to shutdown. Panel is York Optiview Control Center Panel Number: 371-02264-101, 115V 1 Phase 50/60 Hz, S/N KQR-046. Compressor Motor is Reliance 811 HP, 4160 volts, 3600 rpm continuous duty. Includes the starters for all 3 motors. Chiller dimensions: 8.5'W x 18'L x 8'H (compressor adds another 3'). Chiller weight 40,000 lbs. dry. Includes Pump package - skid mounted and contains 2 ITT Bell & Gossett VSCS centrifugal pumps size 10x12-17 designed for 4,000 gpm at 300 ft hd, 1770 rpm. Pump package dimensions: 8.5'W x 16'L x 8'H., Water pumps are 480v. Includes 3 standalone starters - 4160 for compressor, 460v for 2 pumps

Cloud Machine Corp., Cloud horizontal form fill seal Packager Machine No. 277-5, 24 cell 2 1/2 in. centers, 2 HP U.S. Electric Vari-Drive Motor 200-203/460 Volt, 3 Ph., Registration w/ SICK Optic Electronic, WEST heat controllers, Feed Hopper and VFD Feed Belt w/ Dayton 90 VDC Gearmotor, equipped with counter and pneumatic product lane shift. Machine last ran 1 3/8 in. x 2 1/2 in. sachet container 1 gram. Ran on daily basis. Older, good machine.

Cloud Machine Corp., Cloud horizontal form fill seal Packager Machine No. 222-1, 24 cell 2 1/2 in. centers, 3/4 HP Reliance VFD 90 VDC Permanent Magnet Motor w/ Reliance Master XL Gearmotor, Registration w/ SICK Optic Electronic, Watlow heat controllers, Feed Hopper and VFD Feed Belt w/ Dayton 90 VDC Gearmotor, equipped with counter and pneumatic product lane shift. Machine last ran 1 3/8 in. x 2 1/2 in. sachet container 1 gram. Ran on daily basis. Older, reliable machine.

ITW Dynatec, Dyna Pack (Hot Glue), 4-line capability currently equipped w/ two (2) programmable heads (6 ft hose, Part # N2306, Serial No. 93468, 230 Volt), TPC-9 controller, Model No. 114231, S.N. 281382, 120-volt 6 Watt (adjustable delay, length of bead, skip, repeat).

Used Polaris Plate Heat Exchanger. 304 Stainless Steel. Approximately 4,448.50 Square Feet. (330) Stainless steel plates. Rated 150 psi at 284 degrees F. (4) 12" diameter inlet/outlets. Flow rate 3600 gallons per minute. Maximum # of plates 348. Mounted on a painted carbon steel expandable frame. Serial# 11738. Built 2010.

Hapman Flex Screw Conveyor Feed Drive & Pole Stand w/ 2 HP Baldor CM 3558T motor, 208-230/460 Volt, 1725 RPM, 6.5-6.2/3.1 Amps. Hapman Helix Hopper, Screen, and Plastic Top for Hapman 2 inch flexible screw. Approx. 30 x 30 x 36 inch tapered bottom, Serial no. HX 1285, Model P200.

Videojet 1510 (#2), Ink Jet Coding Machine, EXCEL Format, 120/240 Volt, 1Ph, 3 Amp, Serial No. 1009442C 11 ZM, Part No. 399234, w/infrared Fiber Optic Photocell (proximity), O.E.M. Mobile Stand, O.E.M. Static Printhead Stand. Running.

Videojet 1510 (#1), Ink Jet Coding Machine, EXCEL Format, 120/240 Volt, 1Ph., 3 Amp, Serial No. 0911308C11ZH, Part No. 399146, w/infrared Fiber Optic Photocell (proximity), O.E.M. Mobile Stand, O.E.M. Static Printhead Stand. Running.

Videojet 1550 (#3), Ink Jet Coding Machine, EXCEL Format, 120/240 Volt, 1Ph., 3 Amp, Serial No. 1404109C29ZH, Part No. 39582-793-01, w/infrared Fiber Optic Photocell (proximity), O.E.M. Mobile Stand, O.E.M. Static Printhead Stand. Running.

MDI XR-3000 Metal Detector with XR-7F Controller The XR-3000 is an economical metal detector designed to give consistent protection against tramp metal damage. At just a fraction of the cost of the equipment you are protecting, the XR-3000 is a perfect fit. The Diamond Construction Process produces a tough coil that is highly resistant to interference from CB and radio noise as well as vibration. MDI specifically designed a coil that is rugged and will stand up to the demands of the harsh physical environments in which MDI Metal Detectors must endure. Detector and Controller are in very nice condition. These units were used in the plastics industry so they were not in a harsh environment. They were not installed very long. Quantity (3) available, priced separately.

Fortress Technology, Fortress Stealth Metal Detector, 6 in. Gravity System, 2015, Nema 12, Multiple Product Memory, Password Protected, USB Communication Ports for updates and QA Reports. Audible alert for reject and Outputs for Bypass Setup, Exceptional Sensitivity. Currently running 1.0 MM NFe, 1.0 MM Fe, 1.5 MM SS.

LOCK inspection Systems, Met 30+, 3 1/2 in. x 14 in. aperture mounted on conveyor last used with a V/f/f/s machine. Conveyor is 12 in x 10 ft. long horizontally-transitioning to 68 inch long incline where the metal detector is located. Intralox modular conveyor belt. Horizontal section is 6 inches above floor and raises to discharge height of 40 inches. Currently using 1.5 MM NFe, 1.2 MM Fe, 2.0 MM SS

Fortress Technology, Phantom Detection, 5 in. x 14 in. white interlock belt 12 in. x 56 in., SS Frame - 31 in. height (adjustable), Equip Motor Control Panel Model No. C-V60 x 12 KICK, Ser No. 14043 CVF 002924, Voltage 120/130 VAC, Ph 1, Amp. 10.5, 0.5 HP, Frame Model No. SC-CONV-160SSHD12K1CK, Ser. No. CVF 2924, D.O.M. Mar 2013, Nema 12, Multiple Product Memory, Password Protected, USB Communication Ports for updates and QA Reports. Audible alert for reject and pneumatic Slide Air Gate Rejection, Exceptional Sensitivity. Currently running 1.0 MM NFe, 1.0 MM Fe, 1.5 MM SS.

Motor SEW- Euro-Drive motor with brake. Type DV200L4BH31MR, TEC C3PM, volts 230/460. Amps 95/47.5, HP 40, RPM 1760. Brake volts 460AC, Torque 221 lbs/ft. Motor is New - bought in 2009 and has been sitting in controlled temp warehouse since then.

Cloud Packing Table, SS frame w/top painted black, 2 ft. x 4 in x 27 1/2 in. Quantity 3 - priced separately

Paul Mueller Company Accu-Therm Plate Heat Exchanger, Model AT40 B-20. ASME Maximum W. P. 100 psi @ 150F. Previously used with water cooled air compressors. Stored in climate controlled building before and after removal. Approx size 70 1/4" H, 27 " W. Typical max flow GPM H20: 1150. Two available, priced separately. One National Board # 14553, S/N W-30026-2, 1988. Second one National Board # 38064, S/N 321530, 2004.

Pulvocron, a combination pulverizer and classifier built by Bepex in Minneapolis, MN. This piece does not include the classifier. This airswept pulverizer has external fineness adjustment during operation. Size PC76. Model PC-76-A. Powered by GE Electric AC motor, 500HP, 1780 rpm, 460 volts/3/60. Frame 8288S. Mill rated at 600HP, classifier rated at 50 HP. Air movement between 70,000 to 100,000 acfm. This versatile Pulvocron can pulverize in the medium fine, fine, and ultra-fine particle size ranges down to 10 micron top size with only minor adjustment. Actual housing and mechanical moving parts are all stainless steel. Pulvrocron is used in a lot of flour/rice operations. This was removed from a flour plant and was still in use at the time of shut down. Pulvocron was removed early 2013 and the plant was idled in 2010. Condition is good used not much wear internally inside housing. The carbide tips look like they were just replaced before the plant was shut down, they look new Physical size 113" x 197" x 161", weight with motor 35,400 pounds

Worthington Split case pump. Model 5LN522. Size is 8" x 5" - 22" Impeller, epoxy lined. These pumps have been rebuilt and never were used after rebuild. They were back up fire pumps, so they are high head. Rebuilt by HydroAire Services job # 6082-12-11-11. Note Worthington pumps are now backed by Flowserve. Bare pump only - Quantity (2) available - priced separately.

SS Ribbon Blender, 26 x 66 x 30 inch Bowl, 25 cu. Ft., Bottom center unload, 7 ft. Height w/38 inch additional support stands available (the current supports may be unbolted at the bowl and beneath the motor mount for transport), Rotor axle equipped w/ Aaron air glands. 10 H.P., 3 Ph., 230/460. Previously used in Food Grade Kosher supervised plant. Blended spices and sugar sub. Approx shipping dims: roughly 2500 lbs., and we'll put it on a skid that is 38 in. (w) x 96 in. (l) x 42 in. (h).

Ribbon Blender mfg by The J.H. Day Company, Ribbon Blender, 5 Cu. Ft. w/ O.E.M. tri hinge SS top, Serial No. 83781, 16 x 19 x 37 inches (Ht. currently 41 1/2 inches), 1 1/2 HP U.S. Electric Syncro Gear 3 PH Motor, 220/440 Volt, 5.2/2.6 Amps. Excellent shape

NEW Stainless Steel Tank, Capacity (approximate): 7500 gallons, Size 8 ft O.D. x 19 ft Straight, Design pressure given as atmospheric, design temperature 200 degrees F. Shell is 3/16 in. 304/L SS, Heads are 3/16 in. nom. ASME F&D 304/LSS, Nozzles are quantity three (3) 2 inch RFSO and one (1) 12 inch RFSO. Support legs and lifting lugs are carbon steel. 24 inch Manway, External carbon steel is sandblasted and painted with one coat of shop primer. This is a brand new constructed tank so any nozzle placement, size, number can be as customer wished. Lead time: 7-9 weeks - negotiable.